@make[report]
@device[X2700]
@majorheading[Configuring the TelePAC]
@section['log-in' to base by typing @U{BE00}]
@I{N.B.  Use upper case throughout and Backspace (ctrl+H) to rub out.}
@Section{You should get the prompt BASE:, the above sequence should also
be repeated after every BOOT of the system.}
@section[Configure the configuration memory size by typing:-]
@begin[verbatim]
         BASE: @U{MEM}
         MEM:  RESET/N @U{Y}
         MEM:  SIZE/XXXXX @U{31980}
         MEM:  NUMBER OF MENUS/1 @U{RETURN}
         MEM:  NUMBER OF PASSWORDS/1 @U{RETURN}
         MEM:  NUMBER OF X.25 ADDRESSES/32 @U{RETURN}
         MEM:  NUMBER OF BILLING RECORDS/1 @U{RETURN}
         BASE: @U{BOOT}
    this reboots the system setting up the configuration memory.
@end[verbatim]
@section[Configure in the Password 'file' at the Billing records]
@begin[verbatim]
         BASE: @U{MEM}
         MEM:  RESET/N @U{RETURN}
         MEM:  SIZE/XXXXX @U{RETURN}
         MEM:  NUMBER OF MENUS/2 @U{RETURN}
         MEM:  NUMBER OF PASSWORDS/3 @U{RETURN}
         MEM:  NUMBER OF X.25 ADRESSES 32 @U{RETURN}
         MEM:  NUMBER OF BILLING RECORDS/15 @u{RETURN}
         BASE: BOOT

@I{N.B. This must be done in two phases as described.}
@end[verbatim]
@section[Configure the links, PSO1 to PSO8]
@begin[verbatim]
         BASE: >
         EPCI: >
         XXXX: CONF

         XXXX: NAME/XXXX             @U{PSO1}
             : TYPE/NULL             @U{X.25}
             : ADDRESS/B             @U{RETURN}  (N.B. A=DTE, B=DCE)
             : CHANNELS/1            @U{(SEE TABLE)}
             : OPTIONS/NONE          @U{EXT}
             : INITFRAME/SABM        @U{RETURN}
             : T1/30                 @U{RETURN}
             : TRIES/10              @U{30}
             : KLEVEL 2/7            @U{RETURN}
             : KLEVEL 3/2            @U{RETURN}
             : LINE GROUP/0          @U{RETURN}
             : LCGN/0                @U{4}       
             : ADDRESS GROUP/0       @U{RETURN}
             : FRAME SEQ/NORM        @U{RETURN}
             : CALL TIME OUT/5       @U{120}
             : ERROR THRESHOLD/20    @U{RETURN}

         PSO1:
@end[verbatim]
The sequence should now be repeated for PSO1 to PSO8 by typing a  >
to the last prompt.  After typing in the details for PSO8,
type ESC (twice) to get back to BASE:

   The number of channels are as follows:
@begin[verbatim]
    PSO1:  16
       2:  20
       3: 100
       4:  20
       5: 200
       6: 100
       7: 100
       8:  16
@end[verbatim]

@section(Type @U{@B[BOOT]} to initialise all the channels)
@I[N.B. If there is any output from lines during the configuration
procedure - ignore it.]
@section[Configure the logical channels.]
@begin[verbatim]
       BASE: @U{PSO1}
       PSO1:  \  (back slash)
    XXOO(0): @U{CONF}
    XXOO(0): NAME/XXOO @U{P100}
           : DRC MASK/... @U{RETURN}
           : TERMINAL TYPE/ASYN @U{RETURN}
           : CIRCUIT TYPE/CALL+STAT @U{RETURN}
           : OPTIONS/NONE @U{BILL}
           : BUFFERS/2 <ESC>
    P100(0): @U{COPY ALL}
           :
           :
    XXOO(0): <ESC>

       BASE: 
@end[verbatim]
Repeat the above procedure for PSO2 - PSO8 using the following @U{names}.
@begin[verbatim]
    PSO2: P200
       3: P300
       4: P400
       5: P500
       6: P600
       7: P700
       P8: 800
@end[verbatim]

@section[Type in the X.25 table]
@begin[verbatim]
        BASE: X.25
    X.25(0): CONF
    X.25(0): NAME/    BE00
             
           : ADDRESS GROUP/0 @U{RETURN}
           : ADDRESS/        *15003000
           : USER DATA/      @U{RETURN}

    X.25(1): NAME/
@end[verbatim]
Continue the configuration inserting the following names and 
addresses.
@begin[verbatim]
   P200     00015003001-  (N.B. the minus)
   P300       *15003003-
   P400    000015003004-
   P600    000015003006-
   P100    000015003001-
   EI00       *15003091-
  IE101       *15003091-
   P800       *15003008-
   JUNK       *15003*
   P500       *-
@end[verbatim]
Type <ESC> twice to return to BASE:

The TelePAC is now fully configured.